Skip to content
Smithville Plumbing

Guides

How a sump pump works, and how to test it before a storm

How the sump pump in a Smithville basement works, a test you can do yourself with a pail of water before heavy rain, and what to shut off and when to call if it fails mid-storm.

6 min read Updated November 17, 2026.

If your house is in Smithville's Northwest Quadrant, around Station Meadows West or Dunloe, a sump pump is what keeps your basement dry. Houses built there from the 2010s onward send groundwater to a pit in the basement floor. A pump then pushes it out to the yard. Plenty of those houses have only the one pump, the one the builder put in, and it has never been tested. Some post-war houses north of Townline Road also have a sump pit, where the weeping tile was run to a pit instead of the sewer.

This guide explains what the pump is doing down there, how to test it in about ten minutes, and what to do if it stops during a storm.

What is a sump pump actually doing?

Weeping tile is a perforated pipe that runs around the outside of the footings. It collects groundwater before it can push through the foundation walls and floor. In a newer Smithville house that pipe drains into the sump pit, the round or square well in the basement floor, usually covered by a lid.

As water collects in the pit, it lifts a float. When the float rises high enough it switches the pump on. The pump pushes the water up a discharge pipe, through the basement wall and out onto the surface of the yard. As the level drops, the float drops with it and the pump switches off.

There are two other parts to know about:

  • The check valve is a one-way valve on the discharge pipe, a little above the pit. It stops the water already in the pipe from falling back into the pit each time the pump shuts off. A soft thump when the pump stops is normal.
  • The backup pump, if you have one, is a second pump in the same pit, set a little higher and usually running from a battery. It takes over if the main pump fails or the power goes out. A lot of Northwest Quadrant houses don't have one.

In a dry spell the pump can sit idle for weeks. In a wet spring, or after a big rain, it may cycle every few minutes. Either way, the first you'll know it has failed is water on the basement floor, which is why it's worth testing before you need it.

When should you test it?

Test it before the times the pit is likely to fill. In Smithville that means:

  • Before the spring thaw. The Niagara climate normals for Vineland show about 112 cm of snow a year, and all of it has to go somewhere when it melts.
  • Before heavy rain is forecast. The same records show 25 mm or more of rain falling in a single day on four to five days a year, out of roughly 892 mm of precipitation a year.
  • After a long dry stretch, when the pump hasn't run in a while and the float may have stuck.
  • In early winter, to make sure the discharge line outside isn't blocked or frozen. The area averages about 121 days a year with a low at or below freezing.

Last summer a week of heavy rain flooded parts of Niagara. The Township of West Lincoln reported on August 6, 2026 that the impact here was fairly minimal, but it still asked residents whose basements had flooded to report it. It's worth knowing your pump will keep up through a wet week as well as on an ordinary day.

How do you test a sump pump?

You need a pail, a flashlight and somewhere to see the discharge outside.

1. Check the power. The pump should be plugged directly into a wall outlet, not into an extension cord or power bar. If the outlet has a test and reset button, press reset to make sure it hasn't tripped. Some pumps use a piggyback plug, where the float switch plugs into the wall and the pump plugs into the back of it. Make sure both are seated.
2. Lift the lid and look in. You want clean water, or a damp bottom, with no gravel, silt, wrapping or toys in the pit. The float has to be able to move freely without catching on the side of the pit or on the power cord.
3. Fill the pit slowly. Pour water in from a pail until the float rises. The pump should start on its own, drop the water level quickly and then shut off cleanly. Listen as it runs. A steady hum is normal; grinding, rattling or screeching is not.
4. Watch after it stops. If the water level climbs again right away and the pump restarts without more water going in, the check valve is probably letting water fall back down the pipe.
5. Go outside. Find where the discharge comes out and pour another pail in while someone watches. Water should flow freely and land well away from the foundation, sloping away from the house. In winter, make sure the end of the pipe isn't buried in snow or plugged with ice.
6. Test the backup. If you have a battery backup, unplug the main pump and fill the pit again. The backup should start on its own. Check that its alarm sounds, and look at the battery for corrosion on the terminals and for the date it was installed. Then plug the main pump back in.

What are the signs a pump needs attention?

  • It hums but no water leaves the pit. The impeller may be jammed, or the intake may be blocked.
  • It runs constantly, even in dry weather. The float may be stuck up, or water may be getting in faster than the pump can handle.
  • It switches on and off every few seconds. The float may be set badly or the check valve may be failing.
  • You see rust, a cracked housing or a power cord that has been nicked.
  • It's the pump the house was built with and you don't know how old it is.

In most cases a pump that fails the pail test gets replaced rather than repaired. If you have no backup, the best time to add one is when you replace the main pump.

What should you do if the pump fails during a storm?

First, keep yourself safe. If water on the floor is anywhere near outlets, cords or the electrical panel, don't walk into it. Turn off power to the basement at the panel only if you can reach it from a dry spot. Otherwise stay upstairs and call.

If the floor is dry and it's safe to work:

  • Check the outlet and the breaker. Reset whichever has tripped.
  • Look in the pit to see if the float is stuck, and free it if you can.
  • If the pump still won't run, keep the level down with a wet-dry vacuum or a pail until help arrives.
  • Move belongings off the floor and take photos for your insurer.
  • If the basement does flood, report it to the Township of West Lincoln as well, as it asked after the August rain.

Why would you need an emergency plumber?

Most plumbing problems can wait until morning. A few can't, because the damage grows every hour you leave them:

  • The sump pump has stopped and water is rising in the pit or on the floor.
  • Sewage is coming up through the floor drain. In the older village core, around Griffin Street, Station Street and College Street, houses often have a clay sewer pipe with roots at the joints and a floor drain with no sump. Stop using water in the house: no flushing, no laundry, no dishwasher. Every litre you send down comes back up through that drain. Once it's cleared, ask about a backwater valve.
  • A pipe has burst or frozen and split. Shut the main water valve where the line comes into the basement. Then open the lowest cold tap to drain the pipes.

In each case, tell the plumber what the water is doing when you call. They should be able to tell you what to shut off while you wait. You should also get a written price before any part goes in. More on these calls is on our emergency plumber page.

If your pump failed the pail test or you'd like a backup added before the next heavy rain, see sump pumps from Smithville Plumbing.

Still have a question?